Embroidery Fleeces & Films

water-soluble foil for the embroidering of Lace 49cm width, can be ordered per meter and for all other applications, where after washing no fleece shall be seen it can be used for the embroidering of Lace, but also for applying on frottee and high-pile textiles (prevents the sinking of stitches)The thickness of the film is 90 microns.Instructions for Lace-embroidery: 1) hoop in the foil 2) start embroidery 3) spray water at the foil or plunge into the water - ready -

Our proven thermal film BSF (iron-on embroidery film) "FusyFilm" Thermal Foil to make patches ironable on textiles Mounting with electric iron or hot press to the back of embroidered badges. The durability according to the manufacturer is up to 60 degrees. Price per running metre, width: 49cm. Processing instructions: 1. Embroider patches, preferably on SUMa or SUMa-Soft embroidery backing. 2. 2. remove the patch from the embroidery hoop and turn it inside out. 3. preheat the iron or transfer press. Press the thermal foil with the protective paper facing upwards (so that it does not stick to the heating plate) at approx. 130 - 150 degrees Celsius for three to five seconds. 4. peel off the protective paper. 5. Apply a second layer of thermal foil (see point 3); the first layer is absorbed well by the embroidery base, the second layer then adheres very well to the textile. 6. peel off the protective paper. 7. cut out the patch with scissors. 8. iron the patch onto the desired area from the front for approx. 3 seconds using an iron or transfer press. 9. turn the textile onto the reverse side and press from the back for approx. 15 - 20 seconds at approx. 130 - 150 degrees Celsius (ATTENTION: The contact pressure must not be too high, otherwise the patch will become saturated with the adhesive layer and will not adhere to the textile). This causes the adhesive to melt into the fabric and adhere perfectly. Roll 100 m x 49 cm. Apply with an iron or hot press to the back of embroidered patches. Durable up to 60 degrees according to manufacturer's instructions, wash-resistant. Note: The above information is for guidance only. The final result will vary depending on the fabric and working conditions. Preliminary tests on loose fabric recommended.

Precuts in white are currently sold out and will be available again from mid-August. Alternatively, please use the rolls (22cm or 38cm)Fleece 180: middleweight Fleece, 100% Polyester, with 80 gr/qm Features: - Very good stitch representation for best embroidery quality - Stable in both directions - highest quality - stabiliser must be cut - Fixation with spray adhesive - OEKO-TEX certified - 100% polyester - Ironing temperature: 130-150°C - Press-on pressure: 1.5-2.5kgf/cm2 - Washable at: 40-50°C - bleachable - suitable for tumble drying - resistant to cleaning - Absolutely uniform fibre structure - fleece is used in one layer - the fleece becomes softer after washing Suitable for - for 90% of all textiles and fabrics, including very stretchy and thin materials - e.g. piqué fabrics and knitwear Available in black or white: - 10m sample roll in 38cm width - 100m roll in 38cm or 22cm width - Precuts approx. 20cm x 20cm (250 pieces/pack). Why don't we offer fleece rolls in larger widths such as 65 or 100 cm? Our backings in 38cm width are perfectly suitable for 99% of all back embroideries. However, rolls over 40 cm wide cause additional costs due to larger waste and more complex handling with large, heavy rolls. If the width is too small in individual cases, two rolls can simply be laid next to each other. Rolls with a width of 22 cm are available for breast embroidery. Narrow rolls are therefore easy on the wallet and the environment.

  The fleece will be ironed on the left side of the fabric after embroidering and prevents scraping on the skin Size:per meter 35,5cm x 1m roll 35,5cm x 45,7m color Creme or Black Properties: bi-elastic jersey interlining 100% polyester 50gr Processing instructions: Apply with an iron or hot press Ironing temperature 135 - 145 degrees Washable up to 40 degrees Description: The protective fleece is a fusible, bi-elastic jersey interlining used to cover finished stitches on the inside of clothing. This protects the skin from possible scratching or irritation. The bi-elasticity and softness of the protective fleece offers excellent wearing comfort and maximum freedom of movement. It is a very light fabric, which does not shine through the clothing. The protective fleece is perfect for baby and children's clothing to protect sensitive skin from injuries. And it is attached to the back of the embroidery with a heat press or iron.    

Hydrolon - the water-soluble embroidery film features - transparent - water-soluble - easy to tear out due to structured surface - prevents the stitches from sinking into rough and high-pile textiles - is applied in a single layer on the upper side - better representation of filigree embroideries - saves stitches in the embroidery design and thus reduces production time - Individually packaged (light and moisture protection) - Slightly thicker than Avalon, resulting in even finer stitches Suitable for - terry cloth, fleece, knitwear, coarse piqué structures - high-pile materials Available in - 25m short roll in 33cm width - 100m roll in 33cm width

Filmoplast: Self-adhesive tear-off fleece 50gr/qm for all materials to be glued on (e.g. in combination with the multifunctional frame Flat-8). Features - Self-adhesive tear-away stabiliser - 50 g/sqm - 75% cellulose, 25% polyester - OEKO-TEX certified - Coated with polyacrylate - Can be torn in all directions - prevents marks from being made by the stenter frame thanks to the adhesive technique - small fabric cuttings can be perfectly fixed and embroidered - Economical to use, only the "hole" is pasted over again - can also be stabilised with tearing or cutting fleece - No sticking of the needles - Adhesive fleece is used in a single layer Suitable for - all light to medium-weight textiles - Polo shirts, shirts, blouses, collar embroidery, velvet, fleece, leather, ribbons Available in black and white Rolls: dimensions 50cm x 25m

Fleece 480: best Fleece, 100% PES, with 80 gr/qm Features - Very good stitch representation for best embroidery quality - stable in both directions - highest quality tear-away stabiliser - stabiliser can be torn out - Fixing with spray adhesive - OEKO-TEX certified for white - Polyester-cellulose blended fabric - Ironing temperature: 140-150°C - Contact pressure: 1.5-2.5kgf/cm2 - Washable at <40°C - bleachable - suitable for tumble drying - resistant to washing - Absolutely uniform and fine fibre structure - fleece can be used as a single layer or double layer if required - pleasantly soft and stable - to avoid damage when tearing, first tear off the first layer and then the second layer Suitable for - Textiles and fabrics of all kinds, including stretchy and thin materials - e.g. pullovers, softshells, polo shirts, blouses, shirts, fleece Available in black or white: - 10m sample roll in 38cm width - 100m roll in 38cm or 22cm width - Precuts approx. 20cm x 20cm (250 pieces/pack). Why don't we offer fleece rolls in larger widths such as 65 or 100 cm? Our backings in 38cm width are perfectly suitable for 99% of all back embroideries. However, rolls over 40 cm wide cause additional costs due to larger waste and more complex handling with large, heavy rolls. If the width is too small in individual cases, two rolls can simply be laid next to each other. Rolls with a width of 22 cm are available for breast embroidery. Narrow rolls are therefore easy on the wallet and the environment.

SALE: BEST PRICE Hydrolon - the water-soluble embroidery film at a special price properties - transparent - water-soluble - prevents the stitches from sinking into rough and high- pile textiles- is applied in a single layer on the upper side - better representation of filigree embroidery - saves stitches in the embroidery design and thus reduces production time - Individually packaged (protection from light and moisture) Suitable for - terry cloth, fleece, knitted fabrics, coarse piqué structures - high-pile materials Available in - 100m roll in 33cm width

Fleece 350: lightweight non-woven, 100% recycled cotton, non-woven fabric with 50 gr/sqm Features - TOP price/performance ratio - Stable in both directions - Fleece can be torn and is therefore easy to remove - Fastening with spray adhesive - ironing temperature: 160-180°C - Contact pressure: 1.5-2.5kgf/cm2 - Washable at <40°C - bleachable - suitable for tumble drying - resistant to dry cleaning - Variations in fibre structure possible - becomes softer after the first wash cycle - Fleece is used in two layers Suitable for - Textiles and fabrics of all kinds that are stable and not stretchy. - e.g. sturdy jumpers, softshell jackets, firm cotton items Available in black or white: - 10m sample roll in 38cm width - 100m roll in 38cm or 22cm width - Precuts approx. 20cm x 20cm (250 pieces/pack). Why don't we offer fleece rolls in larger widths such as 65 or 100 cm? Our backings in 38cm width are perfectly suitable for 99% of all back embroideries. However, rolls over 40 cm wide cause additional costs due to larger waste and more complex handling with large, heavy rolls. If the width is too small in individual cases, two rolls can simply be laid next to each other. Rolls with a width of 22 cm are available for breast embroidery. Narrow rolls are therefore easy on the wallet and the environment.

Solulon - the water-soluble fleece Rolls: 50cm x 25m properties water-soluble Colour white OEKO-TEX certified 40gr/sqm perfect for lace embroidery can be used in one or two layers Stabilisation of tulle or knitted fabric Suitable for Lace embroidery Embroidery on fine fabrics such as curtains or tulle Embroideries where no stabiliser may be visible after production Stabilisation is carried out as shown in the illustration: 1. hoop the Solulon together with the fabric 2. view of the embroidered reverse side 3. view of the back of the embroidery after dissolving the Solulon with water and ironing the fabric dry 4. view of the finished embroidery file after completion Instructions for lace embroidery: 1. underlay stabiliser (one layer, or two layers for more stability) 2. attach the embroidery directly to the stabiliser 3. briefly dip the embroidery in water - Finished -

Fleece 755: pleasantly soft, thin cutting fleece, 55g, extremely tear-resistant Advantages/areas of application - Soft cutting fleece - 55g - Very good stabilisation of the embroidery - stabiliser must be cut - comfortable to wear due to the flexibility of the material - does not show through on light-coloured, thin fabrics (e.g. shirts, blouses) - Extremely dimensionally stable and heat-resistant - OEKO-Tex certified - 100% polyamide - ironing temperature: 130-150°C - Ironing pressure: 1.5-2.5kgf/cm2 - Washable at: 60°C - bleachable - suitable for tumble drying - resistant to dry cleaning Suitable for - for stretchy and stable materials - e.g. piqué fabrics, shirts, blouses, jumpers Available in black or white: - 10m sample roll in 50cm width - 100m roll in 50cm width - Precuts approx. 20cm x 20cm (250 pieces/pack)Thanks to the precuts, there is no need for time-consuming cutting from the roll and hooping is even faster and more convenient.

Fleece 450: middleweight Fleece, 100% PES, with 50 gr/qm Features - good stitch representation - Stable in both directions - Fleece is tearable and therefore easy to remove - attachment with spray adhesive - OEKO-TEX certified for white - polyester-cellulose blended fabric - Ironing temperature: 140-150°C - Contact pressure: 1.5-2.5kgf/cm2 - Washable at <40°C - bleachable - suitable for tumble drying - resistant to dry cleaning - Absolutely uniform and fine fibre structure - Fleece is used in two layers - pleasantly soft and stable Suitable for - Textiles and fabrics of all kinds that are stable and not very stretchy - e.g. pullovers, softshell jackets, sturdy polo shirts, cotton items Available in black or white: - 10m sample roll in 38cm width - 100m roll in 38cm or 22cm width- Precuts approx. 20cm x 20cm (250 pieces/pack). Why don't we offer fleece rolls in larger widths such as 65 or 100 cm? Our backings in 38cm width are perfectly suitable for 99% of all back embroideries. However, rolls over 40 cm wide cause additional costs due to larger waste and more complex handling with large, heavy rolls. If the width is too small in individual cases, two rolls can simply be laid next to each other. Rolls with a width of 22 cm are available for breast embroidery. Narrow rolls are therefore easy on the wallet and the environment.

Fleece 680: leightwight Fleece, 100% PP, with 80 gr/qm Features: - good stitch representation - soft quality at a favourable price - absolutely even structure, therefore soft on the skin - fleece must be cut - Fixation with spray adhesive - OEKO-TEX certified - 100% polypropylene fibres - Ironing temperature: 80-100°C - Contact pressure: 1.5-2.5kgf/cm2 - Washable at <40°C - bleachable - resistant to cleaning - Fleece is used in one layer Suitable for - For stretchy and thin materials - also suitable for baby clothing and bed linen due to its soft structure Available in black or white: - 10m sample roll in 38cm width - 100m roll in 38cm or 22cm width Why don't we offer fleece rolls in larger widths such as 65 or 100 cm? Our backings in 38cm width are perfectly suitable for 99% of all back embroideries. However, rolls over 40 cm wide cause additional costs due to larger waste and more complex handling with large, heavy rolls. If the width is too small in individual cases, two rolls can simply be laid next to each other. Rolls with a width of 22 cm are available for breast embroidery. Narrow rolls are therefore easy on the wallet and the environment. PLEASE NOTE: The fleece may be ironed at a maximum of 150°C (level 2). (For steam irons, please set the temperature lower). We recommend cutting the stabiliser as short as possible after embroidering and never ironing directly onto the stabiliser. When ironing, it is best to use an intermediate layer so that the stabiliser does not stick to the iron. (The values given are based on experience. Depending on the fabric to be embroidered, the ironing temperature, time and pressure may vary. Please test the correct temperature before starting production).

Fleece 165: middleweight Fleece, 100% Polyester, with 65 gr/qm Features: - good stitch representation - Stable in both directions - medium-strength quality - stabiliser must be cut - Fixation with spray adhesive - OEKO-TEX certified - 100% polyester - Ironing temperature: 130-150°C - Press-on pressure: 1.5-2.5kgf/cm2 - Washable at: 40-50°C - bleachable - suitable for tumble drying - resistant to cleaning - Absolutely uniform fibre structure - fleece is used in one layer - the fleece becomes softer after washing Suitable for - for 90% of all textiles and fabrics, including stretchy and thin materials - e.g. piqué fabrics and knitwear Available in black or white: - 10m sample roll in 38cm width - 100m roll in 38cm or 22cm width - Precuts approx. 20cm x 20cm (250 pieces/pack)- Precuts approx. 38cm x 38cm (250 pieces/pack)Why don't we offer fleece rolls in larger widths such as 65 or 100 cm? Our backings in 38cm width are perfectly suitable for 99% of all back embroideries. However, rolls over 40 cm wide cause additional costs due to larger waste and more complex handling with large, heavy rolls. If the width is too small in individual cases, two rolls can simply be laid next to each other. Rolls with a width of 22 cm are available for breast embroidery. Narrow rolls are therefore easy on the wallet and the environment.

Ironable Fleece 30 g/qm Features: - paper-like - with ironable coating - easily to remove - ideal to fix elastic material 100 m per roll, 35cm width in white and black

Oak leaf to iron on Price per set with one piece for the left side and one piece for the right side colors: gold or silver Instructions: 1. Place the oak leaves as desired on the textile or cap 2. Overlay it with a linen cloth 3. press the iron or ironing press on the desired position for about 3 seconds at level 3 4. Allow to cool